Evo X Ecu Flash Training Course: Introduction

Evo X Ecu Flash Training Course Part 1: Ecu Logic Operation walks you through how the OEM Mitsubishi ECU is designed to work. From understanding how fuel delivery is calculated to the spark timing this basic video is the fundamental building block in our ECU Flash training course.

Evo X Ecu Flash Training Course Part 2: Software Installation & Overview walks you through downloading the ECU Flash software, reading / writing to the ecu, and a general overview how things work. This is the first step to learning how to properly flash tune your Mitsubishi Evolution X.

Evo X Ecu Flash Training Course Part 3: Evo Scan & Megalog Viewer Software Overview walks you a basic over view of how the Evo Scan and Megalog Viewer works to begin our training course.

Evo X Ecu Flash Training Course Part 4: Tephra V7 Rom & XML Files walks you through rom types and XML definition files to properly "patch" the Ecu Flash software to display hidden information. We explore Tephra, RAX V3, and Golden XML patches.

Evo X Ecu Flash Training Course Part 5: ECU Bench Flashing / Rom Switching walks you through changing the ROM ID from a different year Evo X as well as creating a bench flash recovery harnesses.

Evo X Ecu Flash Training Course Part 6: MAF vs Speed Density Tuning walks you through the primary differences between MAF and SD operation modes within the Evo X ecu.

Evo X Ecu Flash Training Course Part 7: Fuel Injector Data & Programming goes through how the fuel mass calculation gets turned into a fuel injector pulse-width to deliver the precise amount of fuel needed during the engine's operation. We learn what the core injector data tables represent a...

Evo X Ecu Flash Training Course Part 8: Closed & Open Loop Fuel Control walks you through how the OEM Mitsubishi engineers designed the ECU to operate with both closed and open loop fuel calculations. We look at the STFT and LTFT fuel trim data to determine how the engine is running in close...

Evo X Ecu Flash Training Course Part 9: Part Throttle Fuel Tuning / Load Comp walks you through how to properly tune idle & part throttle load conditions. We explore how to tell what operation mode the Evo X ecu is using when driving to properly edit MAF or SD tables.

Evo X Ecu Flash Training Course Part 10: WOT Fuel Tuning / Load Comp walks you through how to properly tune full throttle fuel. We explore how to tell what operation mode the Evo X ecu is using when driving to properly edit MAF or SD tables.

Evo X Ecu Flash Training Course Part 11: Omni 4 bar Map Sensor Set-up walks you through configuring your rom file to use the PNP Omni 4 bar map sensor.

Evo X Ecu Flash Training Course Part 12: Spark Timing & Knock Control walks you through how spark timing tables are used to deliver proper torque and horsepower. We explore how the knock control is integrated when knock is detected as well as determine real vs false knock readings when tuning.

Evo X Ecu Flash Training Course Part 13: MIVEC Variable Cam Tuning walks you through tuning the MIVEC variable cam on a 4B11 engine. We explore stock vs tuning MIVEC tables to illustrate the changes to allow for faster spool times, increased torque and horsepower.

Evo X Ecu Flash Training Course Part 14: Idle Control walks you through how the Evo X ecu controls idle rpm based on drive-by-wire throttle plate movement and spark timing feedback.

Evo X Ecu Flash Training Course Part 15: Cranking Fuel & Warm-Up Enrichment walks you through the core tables to edit in order to get proper crank to fire conditions when starting your 4B11 engine. We also explore the warm-up enrichment tables to achieve proper AFR when the engine is warming...

Evo X Ecu Flash Training Course Part 16: Accel Enrichment & Decel Fuel walks you through getting acceleration enrichment fuel dialed in to achieve crisp throttle response from your 4B11 engine. We also explore deceleration fuel tuning to reduce rev hang effect.

Evo X Ecu Flash Training Course Part 17: Boost Control walks you through tuning with load and psi based boost control on the Evo X's. In addition we explore using the RAX V3 patch for further refined boost control.

Evo X Ecu Flash Training Course Part 18: Misc Features & Tables walks you through the various tables and features not yet covered in the training course.

Evo X Ecu Flash Training Course Part 19: SST Transmission Tuning walks you through SST transmission operation, data logging, and programming to ensure proper clutch pressure and slippage.

Evo X Ecu Flash Training Course Part 20: Ethanol Fuel Tuning walks you through how to tune with ethanol based fuels on the Evo X ecu programming. We explore using a supplied excel calculator to properly populate the injector scalar and cranking fuel tables.

Evo X Ecu Flash Training Course Part 21: Tehpra V3 Rom Map Switching walks you through the basics of the Tehpra V3 rom and the map switching features.

Evo X Ecu Flash Training Course Part 22: Tehpra V3 Rom Meth Fail Safe walks you through how to utilize the meth fail safe feature to prevent engine damage in the event a meth injection kit fails under WOT conditions.

Evo X Ecu Flash Training Course Part 23: Tehpra V3 Rom Launch Tables walks you through how to use the launch table feature in order to generate more boost while using the 2 step / stationary limiter.

Evo X Ecu Flash Training Course Part 23: Tehpra V3 Rom Flex Fuel walks you through using the flex fuel tuning feature. We explore using an excel calculator to input the proper injector scaling and cranking fuel tables for the flex fuel parameters.

Ecu Flash Evo X Live Training Part 1: 2011 Evo X MR - Bolt Ons walks you through set-up and configuration of the base map to begin our live training session. We look at configuration of everything from the MAF calibration table to the SST transmission tables.

Ecu Flash Evo X Live Training Part 2: 2011 Evo X MR - Bolt Ons walks you through the basic fuel and load calc / load registration tuning process on a Evo X MR. We explore how to tell if the SST transmission clutch pressure and slippage is correct to avoid damage.

Ecu Flash Evo X Live Training Part 3: 2011 Evo X MR - Bolt Ons walks you through how to properly tuned the load calc registration, fuel, spark, and closed loop boost control on a Evo X MR.

Ecu Flash Evo X Live Training Part 4: 2011 Evo X MR - Bolt Ons walks you through set up and configuration of the Tephra V3 rom. We explore how to properly transfer the key tables and data over to a Tephra V3 rom as well as the validation process to ensure the engine still calibrated. In additio...

Ecu Flash Evo X Live Training Part 5: 2011 Evo X MR - Bolt Ons takes a look at real world validation process of the tuning that was done on the chassis dyno. We explore how to review data logs to check for proper fuel, spark, boost, knock, and SST transmission control in real world racing condit...

ECU Flash Evo X Live Training Part 1: 2011 Evo X GSR Flex Fuel walks you through the base map creation process on a 800 whp+ flex fuel 2011 Evo X GSR using a Tehpra V3 rom.

ECU Flash Evo X Live Training Part 2: 2011 Evo X GSR Flex Fuel explores getting a 800 whp+ Evo X GSR fired up and running on a Tephra V3 rom. We explore fuel calibration and idle tuning to ensure proper engine operation before full throttle tuning is performed.

ECU Flash Evo X Live Training Part 3: 2011 Evo X GSR Flex Fuel walks you through the full throttle calibration techniques for fuel, spark, MIVEC, and boost control on a 800 whp+ flex fuel Evo X GSR using the Tephra V3 rom.

ECU Flash Evo X Live Training Part 4: 2011 Evo X GSR Flex Fuel walks you through tuning a 800 whp+ Evo X flex fuel GSR using the Tephra V3 rom. We explore high boost tuning on ethanol with fuel, spark, MIVEC, and boost control to achieve high power levels.

ECU Flash Evo X Live Training Part 5: 2011 Evo X GSR Flex Fuel walks you through cold start / warm-up enrichment, launch control / anti-lag, and drivability testing off the chassis dyno.

Evo X Ecu Flash Training Course Part 25: Virtual Dyno Software walk you through using Virtual Dyno software to plot horsepower and torque production of the engine while calibrating. This will replicate a chassis dyno to measure changes when tuning spark timing, MIVEC, boost control, and more!

Evo X Ecu Flash Training Course Part 26: Tactrix 2.0 SD Card Logging walks you through setting up remote data logging using an SD card. We explore custom code provided in the training course folder to allow the SD card to log properly using the Tactrix 2.0 cable.

Evo X Ecu Flash Training Course Part 27: Shift Knock walks you through how to properly recognize and tune out shift knock on Evo X applications.

Evo X Ecu Flash Training Course Part 28: Idle Airflow Table walks you through how and when to edit the idle airflow table to get extremely large cams, big injectors, or aftermarket throttle bodies to idle properly.

Ecu Flash Evo X Live Training Part 1: 2014 Evo X GSR Flex Fuel walks you through the basemap creation using a Tephra V3 rom on a flex fuel 2014 Evo X GSR. We explore programming fuel, spark timing, MIVEC, and much more!

Ecu Flash Evo X Live Training Part 2: 2014 Evo X GSR Flex Fuel takes an in-depth look at tuning fuel & spark timing for idle and part throttle driving conditions.

Ecu Flash Evo X Live Training Part 3: 2014 Evo X GSR Flex Fuel walks you through tuning fuel, spark timing, and boost control on 93 octane using a Tephra V3 rom.

Ecu Flash Evo X Live Training Part 4: 2014 Evo X GSR Flex Fuel walks you through tuning fuel, spark timing, and boost control on E90 ethanol fuel using a Tephra V3 rom.

Ecu Flash Evo X Live Training Part 5: 2014 Evo X GSR Flex Fuel takes an in-depth look at drivability and full throttle performance off the chassis dyno in real-world conditions.

Ecu Flash Evo X Live Training Part 1: 2011 Evo X MR Flex Fuel walks you through the base map creation process from start to finish using a Tephra V3 rom.

Ecu Flash Evo X Live Training Part 3: 2011 Evo X MR Flex Fuel walks you through the full throttle calibration process off of the wastegate spring level. We explore how to properly dial in the fuel, spark, and MIVEC mapping during the calibration process to get the best powerband possible.

Ecu Flash Evo X Live Training Part 2: 2011 Evo X MR Flex Fuel walks you through the process of dialing in the idle / cruise fuel trims using Evo Scan and Megalogviewer HD software. We explore how to verify if the MAF scaling is correct based on logged load calculations and how to make changes to...

Ecu Flash Evo X Live Training Part 5: 2011 Evo X MR Flex Fuel breaks down the flex fuel tuning option using the Tehpra V3 rom. We explore how to use the flex fuel feature with a fuel flow limited fuel system to help make additional safe power.

Ecu Flash Evo X Live Training Part 4: 2011 Evo X MR Flex Fuel walks you through the boost control tuning process using a 3 port boost solenoid. We explore setting up the feed-forward base duty cycle table along with the target boost tables to achieve steady and repeatable boost levels.

Ecu Flash Evo X Live Training Part 6: 2011 Evo X MR Flex Fuel walks you through start-up / warm-up fuel tuning process. We also explore checking drivability off the chassis dyno to ensure a final stamp of approval.