AEM Series 1 Introduction

Follow along as lead instructor, Jeff Evans, walks you through how to download and install the AEM Pro and AEM Log software to begin the training course.

Follow along as lead instructor, Jeff Evans, walks you through the basic features and functions of the AEM Pro software to begin the training course.

Follow along as lead instructor, Jeff Evans, walks you through setting up the AEM Pro page layouts to save time while tuning your AEM Series 1.

Follow along as lead instructor, Jeff Evans, walks you through how to program your injector dead time / offset as well as configuring the basic sensor inputs.

Follow along as lead instructor, Jeff Evans, walks you through how to program your outputs such as a radiator fan, secondary fuel pump, and many other functions.

Follow along as lead instructor, Jeff Evans, walks you through how the cranking fuel, post-start fuel trim, and warm up enrichment trims work and how to properly program them.

Follow along as lead instructor, Jeff Evans, walks you through working with the main fuel table and how to properly rescale the microbit/sec to gain precise fuel delivery.

Follow along as lead instructor, Jeff Evans, walks you through working with the o2 feedback control to dial in your main fuel table, and provide a long term correction after you have completed tuning.

Follow along as lead instructor, Jeff Evans, walks you through working with the acceleration fuel enrichment and deceleration fuel cut off features within the AEM Pro software.

Follow along as lead instructor, Jeff Evans, walks you through working with the main spark timing table and modifier tables.

Follow along as lead instructor, Jeff Evans, walks you through working with the boost compensation fuel trim modifier table to provide a linear increase in fuel delivery based on manifold pressure changes.

Follow along as lead instructor, Jeff Evans, walks you through working how to tune the idle control in both the basic and advanced settings.

Follow along as lead instructor, Jeff Evans, walks you through working with the knock control feature in the AEM Pro software.

Follow along as lead instructor, Jeff Evans, walks you through working how to set-up your main rev limiter and 2 step rev limiter features within the AEM series 1 software. We also take a look at working with the drag race anti-lag feature to build boost off the line for a turbocharged engine.

Follow along as lead instructor, Jeff Evans, walks you through working how to program your coil dwell settings, and work with the injector phasing table to optimize the injector timing.

Follow along as lead instructor, Jeff Evans, walks you through working how the nitrous control programming works, and strategies to implement when tuning with nitrous.

Follow along as lead instructor, Jeff Evans, walks you through working how to work with the boost control feature in the AEM Pro software. We take a look at both open and closed loop control strategies, as well as the workflow to dial in the closed loop boost tables.

Follow along as lead instructor, Jeff Evans, walks you through how to program VTEC equipped Honda engines. We cover the basic output control to utilizing separate fuel and spark timing tables for high cam operation.

Follow along as lead instructor, Jeff Evans, walks you through different tuning strategies working with water/meth injection within the AEM Pro software.

Follow along as lead instructor, Jeff Evans, walks you through various misc programming features within the AEM Pro software such as VSS calibration, gear ratios, Tacho output, TPS based fuel tables, and more.

Follow along as lead instructor, Jeff Evans, as he walks you through how to capture data logs by PC/laptop or the on-board logging feature. We also take a look what on-board logging channels are useful for logging purposes.

Follow along as lead instructor, Jeff Evans, as he walks you through an introduction to using the AEM Log software to review data logs captured in AEM Pro.

Follow along as lead instructor, Jeff Evans, as he walks you through using the overlay option in the AEM Log software to compare two different log files.

Follow along as lead instructor, Jeff Evans, as he walks you through reviewing a data log from a tuning session in the AEM Log software.

Introduction video to the AEM Series 2 training course.

Part 1 of the the AEM series 2 training course walks you through installing the AEM Tuner software onto your laptop, as well as a brief overview of the tuning template and calibration file.

Part 2 of the the AEM series 2 training course walks you through working with calibration files to begin the tuning process. We learn how to rescale table breakpoints, math functions, and proper saving of the calibration file.

Part 3 of the the AEM series 2 training course walks you through working getting online with the EMS, uploading a calibration file, and firmware flashing process.

Part 4 of the the AEM series 2 training course does a software over view and sets up our workspace for future training videos.

AEM Series 2 Part 5 takes a look at working with our main fuel table and the fuel compensation modifiers, such as air temp and coolant temp. We take an in-depth look at the main fuel table rescaling based on injector size and the microbit/sec and why it's so important.

AEM Series 2 Part 6 takes a look at setting up basic and advanced inputs in the AEM Tuner software.

AEM Series 2 Part 7 takes a look at setting up cranking fuel, post start fuel and warm-up enrichment fuel tables.

AEM Series 2 Part 8 takes a look at setting up idle control using the AEM Tuner software.

AEM Series 2 Part 9 takes a look at setting up the closed loop o2 control feedback in the AEM Tuner software.

AEM Series 2 Part 10 takes a look at setting up and tuning acceleration enrichment and deceleration fuel cut off feature in the AEM Tuner software.

AEM Infinity training course part 11 walks you through the post-start and warm-up enrichment tables found within the AEM Infinity Tuner software and how to properly tune them.

AEM Series 2: Part 12 takes a look at how to properly configure and work with the fail-safe features found in the AEM Tuner software.

AEM Series 2: Part 13 takes a look at how the knock control feature works, how to program fuel/ignition timing based on knock control, programming resonant & flat response knock sensors, and much more!

AEM Series 2: Part 14 takes a look at how to properly configure outputs such as radiator fan, fuel pump, VTEC, ignition coils and fuel injectors. As an added bonus we look at how to utilize the outputs feature to test coil and injectors for diagnostic purposes.

AEM Series 2: Part 15 takes a look at how the boost control feature works within the AEM Tuner software, how to program it and what to look for in the data to verify its set-up and working properly.

AEM Series 2: Part 16 takes a look at the staged fuel injection feature. We go through how to configure the additional fuel injectors, as well as dialing in the staged injection table.

AEM Series 2: Part 17 takes a look at the boost compensation feature. We study how the boost compensation modifier is tied to the main fuel table, and how we can use it to greatly simplify tuning on a forced induction engine.

AEM Series 2: Part 18 takes a look at the nitrous control feature. We study how the nitrous control feature works, how to properly program it, and alternative uses.

AEM Series 2: Part 19 takes a look at the different rev limiter features we have available in the AEM Series 2. From the main rev limiter, 2-Step, and 3-Step limiter features we cover how the limiters work independently and interact with each other.

AEM Series 2: Part 20 takes a look setting up the drag race anti-lag feature. We run the engine simulator to illustrate how the feature works, and how to properly program the anti-lag to work in conjunction with the 2 step rev limiter.

AEM Series 2: Part 21 walks you through how to properly calibrate the vehicle speed sensor, as well as configuring the gear ratio detection table. Both are vital for utilizing many speed and gear based features within the series 2 software.

AEM Series 2: Part 22 walks you through how the injection timing table works with the series 2, as well as working with the coil dwell tables to dial in your ignition coil dwell.

AEM Series 2: Part 23 walks you through how the variable cam control feature works within the AEM series 2. We cover how to set-up the background tables, as well as the tuning process using the variable cam target tables.

AEM Series 2: Part 24 walks you through how to set-up the shift cut feature using a clutch pressure sensor or strain gage.

AEM Series 2: Part 25 walks you through how to wire, configure and program the flex fuel tuning feature. We take an in-depth look at the flex fuel programming on the engine simulator to illustrate how the flex tables work in conjunction with the main tables.

AEM Series 2: Part 26 walks you through how use the laptop and on-board data logging within the AEM Tuner software. We take a specific look at what channels you should add to your on-board logging to capture the correct data.

AEM Series 2: Part 27 walks you through downloading the AEM Data software, configuring custom templates and opening data log files.

AEM Series 2: Part 28 walks you through reviewing the fuel tuning process based on reading data logs in AEM data software and making changes to the calibration file in the AEM Tuner software.

AEM Series 2: Part 29 walks you through reviewing the ignition timing & knock control tuning process based on reading data logs in AEM data software and making changes to the calibration file in the AEM Tuner software.

AEM Series 2: Part 30 walks you through reviewing the boost control tuning process based on reading data logs in AEM data software and making changes to the calibration file in the AEM Tuner software.

AEM Series 2: Part 31 walks you through reviewing the closed loop fuel tuning process based on reading data logs in AEM data software and making changes to the calibration file in the AEM Tuner software.

AEM Series 2: Part 32 walks you through reviewing data logs for diagnostic purposes in the tuning process.

AEM Series 2: Part 33 walks you through setting up the math and overlay features to aid in the data log review process and tuning.

AEM Series 2: Part 34 walks you through reviewing track data logs and configuring the 3 step rev limiter based on the information reviewed in the logs.

AEM Series 2: Part 35 walks you through a mid 8 second 1/4 mile pass to illustrate how the 3 step rev limiter functions, as well as taking a look at launch control and boost control.

Follow along as lead instructor, Jeff Evans, walks you through how to utilize the Virtual Dyno software to produce horsepower and torque readings based data log files using AEM Series 2. We explore the process of how to properly export data from AEM Data log software to view within the Virtual D...

AEM Series 2 Part 37: Megalog Viewer HD Software training tutorial shows you a different approach to data analysis to more efficiently tune your main fuel table and analyze large data log files.

Introduction to AEM Infinity training course.

AEM Infinity training course part 1 walks you through downloading and installing the software onto your laptop, as well as downloading the firmware file specific for your Infinity.

AEM Infinity training course part 2 walks you through installing the firmware image onto the Infinity, as well as working with the session ID's to begin the tuning process.

AEM Infinity training course part 3 walks you through basic software navigation to get comfortable with the layout of the Infinity Tuner software.

AEM Infinity training course part 4 walks you through both laptop & on-board data logging using the AEM Infinity Tuner software. We also take an in-depth look at how to format a new USB storage drive using the on-board logging feature.

AEM Infinity training course part 5 walks you through editing existing layout/templates for tuning, creating a new page within the layout, and creating a fresh layout.

AEM Infinity training course part 6 walks you through setting up our basic configuration and sensor data. This includes things such as injector information, basic sensors, engine details and other pertinent information that we need to establish before tuning begins.

AEM Infinity training course part 7 walks you through setting up additional inputs to the Infinity such as additional pressure & temp sensors, switches, speed sensors and more.

AEM Infinity training course part 8 walks you through configuring outputs to control items such as fuel pump, radiator fan, a/c clutch, VTEC & tachometer.

AEM Infinity training course part 9 walks you through how the Infinity system works with injector characterization data differently for a return and return-less fuel system. As an added bonus we take a look at adding a fuel pressure sensor to our fuel system, and wiring the sensor into the Infin...

AEM Infinity training course part 10 walks you through the cranking fuel trim tables found within the AEM Infinity Tuner software and how to properly tune them.

AEM Series 2 Part 11 takes a look at the main ignition table, ignition modifiers and syncing ignition timing process.

AEM Infinity training course part 12 walks you through how to set-up and work with the idle control programming found in the AEM Infinity software.

AEM Infinity training course part 13 walks you through working with our main VE fuel table, closed loop fuel tuning techniques, wiring in an external wideband controller for closed loop control, and utilizing the fuel trim modifier tables.

AEM Infinity training course part 14 walks you through working with our main ignition timing table and spark modifier tables.

AEM Infinity training course part 15 walks you through the acceleration enrichment and deceleration fuel cut found in the Infinity Tuner software.

AEM Infinity training course part 16 walks you through working with the protection fail-safe features found in the Infinity software using our engine simulator to see cause/effect during the programming of the tables.

AEM Infinity training course part 17 walks you through setting up and tuning with the flex fuel feature in Infinity Tuner software.

AEM Infinity training course part 18 walks you through setting up and configuring the boost control feature found in Infinity Tuner software. We also take a look at closed loop PID control and how to successfully implement it during tuning.

AEM Infinity training course part 19 walks you through setting up and configuring traction control. Using our engine simulator we take a very detailed look at how to do a rolling wheel speed calibration, and how the traction control system works based on the many tables that need to be properly...

AEM Infinity training course part 20 walks you through setting up and configuring the main rev limiter, 2 step rev limiter and 3 step rev limiters.

AEM Infinity training course part 21 walks you through setting up and configuring the launch anti-lag and rolling anti-lag features.

AEM Infinity training course part 22 walks you through setting up and configuring the staged fuel injection feature in the AEM Infinity Tuner software.

AEM Infinity training course part 23 walks you through setting up and configuring per cylinder knock control in the AEM Infinity Tuner software.

AEM Infinity training course part 24 walks you through setting up and configuring the nitrous control feature found in the AEM Infinity Tuner software.

AEM Infinity training course part 25 walks you through setting up and configuring both intake and exhaust variable cam control in the AEM Infinity Tuner software.

AEM Infinity training course part 26 walks you through using the diagnostics functions of the AEM Infinity Tuner software to help troubleshoot no start, misfiring and cam/crank sensor issues.

AEM Infinity training course part 27 walks you through how to calculate gear position for any gear ratio based tables.

AEM Infinity training course part 28 walks you through to set-up the shift cut feature using a clutch switch, clutch pressure sensor or strain gage.

AEM Infinity training course part 29 walks you through using the secondary volumetric efficiency table for characterizing the high cam operation in VTEC. We also take a look at other usages for the secondary VE table.

AEM Infinity training course part 30 walks you through using the on-board datalogging feature. The logger allows 100 channels to be captured, and we explore populating the data list with relevant channels to take advantage of this awesome feature.

AEM Infinity training course part 31 walks you through downloading, installing and configuring AEM Data software to review the on-board datalog files.

AEM Infinity training course part 32 walks you through reviewing an on-board datalog in the AEM Data software, as well as learning how to utilize the software features such as math channels and overlays.

AEM Infinity training course part 34 walks you through using the diagnostic firmware to test injector, coil and low side outputs.

AEM Infinity training course part 33 walks you through how to read a datalog from a high hp FWD drag vehicle using the 3-Step, Traction Control & Closed Loop Boost Control features.

Follow along as lead instructor, Jeff Evans, walks you through how to utilize the Virtual Dyno software to produce horsepower and torque readings based data log files using AEM Infinity. We explore the process of how to properly export data from AEM Data log software to view within the Virtual D...

AEM Infinity training course part 36 walks you through utilizing the multi-tune feature within the AEM Infinity Tuner software. We look at utilizing either a basic on/off switch or trim pot to allow the map switching to occur on the fly.

AEM Infinity training course part 37 walks you through how to set-up custom outputs within the AEM Infinity Tuner software. We explore setting up more commonly used custom outputs such as secondary fuel pump control or secondary boost control solenoids.

AEM Infinity training course part 38 walks you through how to use a simple hack to open up onboard data log files (.itlog) within the AEM Infinity Tuner software for editing purposes.

AEM Infinity Part 39: Megalog Viewer HD Software shows you an alternate way to process data logs in a 3rd party data logging software. We specifically take a look at using the Histogram overlay feature to more efficiently tune the main VE table.