Evo X Ecu Flash Training Course: Introduction

Evo X Ecu Flash Training Course Part 1: Ecu Logic Operation walks you through how the OEM Mitsubishi ECU is designed to work. From understanding how fuel delivery is calculated to the spark timing this basic video is the fundamental building block in our ECU Flash training course.

Evo X Ecu Flash Training Course Part 2: Software Installation & Overview walks you through downloading the ECU Flash software, reading / writing to the ecu, and a general overview how things work. This is the first step to learning how to properly flash tune your Mitsubishi Evolution X.

Evo X Ecu Flash Training Course Part 3: Evo Scan & Megalog Viewer Software Overview walks you a basic over view of how the Evo Scan and Megalog Viewer works to begin our training course.

Evo X Ecu Flash Training Course Part 4: Tephra V7 Rom & XML Files walks you through rom types and XML definition files to properly "patch" the Ecu Flash software to display hidden information. We explore Tephra, RAX V3, and Golden XML patches.

Evo X Ecu Flash Training Course Part 5: ECU Bench Flashing / Rom Switching walks you through changing the ROM ID from a different year Evo X as well as creating a bench flash recovery harnesses.

Evo X Ecu Flash Training Course Part 6: MAF vs Speed Density Tuning walks you through the primary differences between MAF and SD operation modes within the Evo X ecu.

Evo X Ecu Flash Training Course Part 7: Fuel Injector Data & Programming goes through how the fuel mass calculation gets turned into a fuel injector pulse-width to deliver the precise amount of fuel needed during the engine's operation. We learn what the core injector data tables represent and h...

Evo X Ecu Flash Training Course Part 8: Closed & Open Loop Fuel Control walks you through how the OEM Mitsubishi engineers designed the ECU to operate with both closed and open loop fuel calculations. We look at the STFT and LTFT fuel trim data to determine how the engine is running in closed lo...

Evo X Ecu Flash Training Course Part 9: Part Throttle Fuel Tuning / Load Comp walks you through how to properly tune idle & part throttle load conditions. We explore how to tell what operation mode the Evo X ecu is using when driving to properly edit MAF or SD tables.

Evo X Ecu Flash Training Course Part 10: WOT Fuel Tuning / Load Comp walks you through how to properly tune full throttle fuel. We explore how to tell what operation mode the Evo X ecu is using when driving to properly edit MAF or SD tables.

Evo X Ecu Flash Training Course Part 11: Omni 4 bar Map Sensor Set-up walks you through configuring your rom file to use the PNP Omni 4 bar map sensor.

Evo X Ecu Flash Training Course Part 12: Spark Timing & Knock Control walks you through how spark timing tables are used to deliver proper torque and horsepower. We explore how the knock control is integrated when knock is detected as well as determine real vs false knock readings when tuning.

Evo X Ecu Flash Training Course Part 13: MIVEC Variable Cam Tuning walks you through tuning the MIVEC variable cam on a 4B11 engine. We explore stock vs tuning MIVEC tables to illustrate the changes to allow for faster spool times, increased torque and horsepower.

Evo X Ecu Flash Training Course Part 14: Idle Control walks you through how the Evo X ecu controls idle rpm based on drive-by-wire throttle plate movement and spark timing feedback.

Evo X Ecu Flash Training Course Part 15: Cranking Fuel & Warm-Up Enrichment walks you through the core tables to edit in order to get proper crank to fire conditions when starting your 4B11 engine. We also explore the warm-up enrichment tables to achieve proper AFR when the engine is warming up ...

Evo X Ecu Flash Training Course Part 16: Accel Enrichment & Decel Fuel walks you through getting acceleration enrichment fuel dialed in to achieve crisp throttle response from your 4B11 engine. We also explore deceleration fuel tuning to reduce rev hang effect.

Evo X Ecu Flash Training Course Part 17: Boost Control walks you through tuning with load and psi based boost control on the Evo X's. In addition we explore using the RAX V3 patch for further refined boost control.

Evo X Ecu Flash Training Course Part 18: Misc Features & Tables walks you through the various tables and features not yet covered in the training course.

Evo X Ecu Flash Training Course Part 19: SST Transmission Tuning walks you through SST transmission operation, data logging, and programming to ensure proper clutch pressure and slippage.

Evo X Ecu Flash Training Course Part 20: Ethanol Fuel Tuning walks you through how to tune with ethanol based fuels on the Evo X ecu programming. We explore using a supplied excel calculator to properly populate the injector scalar and cranking fuel tables.

Evo X Ecu Flash Training Course Part 21: Tehpra V3 Rom Map Switching walks you through the basics of the Tehpra V3 rom and the map switching features.

Evo X Ecu Flash Training Course Part 22: Tehpra V3 Rom Meth Fail Safe walks you through how to utilize the meth fail safe feature to prevent engine damage in the event a meth injection kit fails under WOT conditions.